As reported earlier, the FIA aims to make motorsport more sustainable and more environment-friendly. The pursuit of these objectives cover various forms of motorsport, including the World Rally Championship (WRC) which, this year, sees the introduction of hybrid technology mandatory for what are known as Rally1 cars. The plug-in hybrid unit, including all necessary components and software, will be common, with the potential for more freedom of development in 2024.
TOYOTA GAZOO Racing, Hyundai Motorsport and M-Sport Ford have fully committed to the WRC from 2022 to 2024 and will run Rally1 cars. They will use a plug-in hybrid powertrain with an existing 1.6-litre turbocharged petrol engine, and must also run on 100% fossil-free fuel to reduce CO2 emissions.
The system’s output is more than 500 ps, with 100 kW contributed by the electric motor which draws its energy from a 3.9 kWh battery pack. Hybrid Electric Vehicle Zones created close to service parks and ceremonial start areas during all rounds of the WRC will require Rally1 crews to demonstrate that they can run in full electric mode over a specified route highlighted in the roadbook.
New safety issues
The introduction of high-voltage hybrid powertrains brings new safety issues for the crew as well as spectators and the FIA has issued new requirements specifically for Rally1 cars. Firstly, there must be two pairs of Class-0 gloves carried in each car capable of withstanding 1,000 volts. These must be easily accessible for the driver and co-driver in the event of an emergency when they are getting out of their car.
Warnings on exterior of Rally1 cars
On the outside, the Rally1 cars are identifiable by an ‘HY’ graphic on the side door panels. Spectators are being warned to look out for this graphic so that they will take care. In rallies, it is not unusual for spectators to rush to a car that has crashed or gone off the road to assist and if a Rally1 car is damaged in certain areas, electric current could leak onto the bodywork.
The organisers therefore want to ensure that there are no incidents of people being electrocuted, and each car has safety lights on the windscreen and both side pillars. These lights will be green when the car is safe to touch. A flashing red light with an audible warning means a car is unsafe to touch.
Second round underway
The 2022 WRC is currently running its second round in Sweden after the opening round in Monte Carlo last month which was won by M-Sport Ford. TOYOTA GAZOO Racing’s Kalle Rovanpera got off to a strong start during the speed test in his Toyota GR Yaris Rally1. He gets to start first today though that is not necessarily an advantage in a winter rally.
With Sweden not part of Sebastien Ogier’s programme of selected rallies this season, Esapekka Lappi will make his first start with the team’ since 2018. Rovanpera will open the road as the highest-placed driver in the standings after finishing fourth and winning the Power Stage on Rallye Monte-Carlo.
Elfyn Evans was part of the lead battle on Round 1 before a small but costly mistake ended his chances of a strong result. He will hope for a repeat of the championship’s last visit to Sweden in 2020 when he scored his first victory for Toyota. As on every round this season, Takamoto Katsuta will drive an additional GR YARIS Rally1.
M-Sport Ford’s Craig Breen has a strong track record on snow to date. The Irishman is keen to show his ability on the high-speed snow tests in search of a second consecutive podium result. Off the back of his first ever WRC stage win, Gus Greensmith completed a small Norwegian National event in a Ford Fiesta Rally2 to help acclimatise to the specialist conditions and driving style. The young Englishman is aiming to build on his Monte Carlo result and looking for his first loose surface stage win.
The Hyundai Motorsport team, which had a bad first outing of the season, has a previous winner of Rally Sweden – Thierry Neuville who won in 2018. “Rallying is always a bit more spectacular on snow with the studded tyres,” he said . “Usually, as the stages are quite fast, you have to lean into the snowbanks and drive sideways a bit more. You have to be slightly more brutal to get the studs to grip into the ground.”
Closer to Arctic Circle this year
Conditions are extreme, though not unusual for Rally Sweden which is on ice and snow, with temperatures well below 0°C. There is also likely to be rain during the event which is run in the remote forests of north-eastern Sweden, closer to the Arctic Circle. There are 17 stages over 265 kms.
The various stages of Rally Sweden this year.
The stages will all be brand-new to the WRC but the characteristics that make it one of the most popular and spectacular rallies on the calendar will remain. Special studded tyres bite into the surface to provide grip on roads that are lined with snow banks, which drivers lean on to carry more speed through the corners.
Following the introduction of the new Mercedes-Benz S-Class (W223) last December, Mercedes-Benz Malaysia can now provide the price of the model. Only one version is available – the S 580 e Plug-In Hybrid – and it is priced at RM698,744 (excluding insurance), As it is assembled locally at the company’s facility in Pekan, Pahang, it can have full exemption of sales tax until June 30, 2022, which would be big savings for customers.
The flagship of the Mercedes-Benz range has been on sale in Malaysia since the 1970s, with over 18,000 cars sold to date, almost all assembled locally. The model’s history goes back to the W180 of 1954 although it was only in 1972 that it came to be known as the ‘S-Class’. Globally, more than 4 million units have been sold since the early 1970s.
The W223 is the seventh generation and as with every generation before, the new S-Class brings with it advanced technologies. In fact, this model has often introduced many new technologies, especially in the area of safety, that it shows ‘the future of motoring’. For example, in 1980, the W126 generation was the first production car in the world to be equipped with an airbag system.
With Mercedes-Benz now putting its full commitment to electrification during this decade, the S-Class also leads the way and for the Malaysian-assembled model, a plug-in hybrid (PHEV) powertrain is the only one offered. Hybrid powertrains are not new to Mercedes-Benz in Malaysia and have been available with some models (including the S-Class) over the past 8 years.
Mercedes-Benz Malaysia has its own plant in Pekan, Pahang, where the latest S-Class and other models are assembled. (File image)
For the latest S-Class, the model is designated S 580 e but its engine not 5.8 litres. It is actually an in-line 6-cylinder petrol engine of 3 litres and works with an electric motor which generates 110 kW with 440 Nm. The engine’s output is 367 bhp/270 kW with 500 Nm of torque and the combined output can propel the S 580e from 0 to 100 km/h in a claimed 5.2 seconds and up to a top speed of 250 km/h.
If conditions permit, it is possible to run only on electricity for up to 100 kms. When the lithium-ion battery is empty, ‘refuelling’ will take up to 2.5 hours, depending on the charging method. One concern owners have is the cost of the battery pack if it needs to be replaced as it is pretty expensive. But for the first 8 years or a maximum of 100,000 kms, Mercedes-Benz Malaysia will provide warranty coverage which should offer some peace of mind.
Showcase for new technologies
New for this S-Class is DIGITAL LIGHT, which offers significantly better illumination from the headlamps. Each light module has 3 extremely powerful LEDs with light that is refracted and directed by 1.3 million micro-mirrors. The resolution is therefore more than 2.6 million pixels per vehicle, allowing highly precise light distribution.
The millions of pixels allow the lighting pattern to be precisely shaped so that maximum illumination levels can be provided without blinding oncoming drivers. Light/shadow graduations and the light distribution of all the other adaptive light functions are also realised with considerably more precision, optimising illumination in all ambient lighting conditions.
Aerodynamic efficiency has always been important for cars as lower wind resistance of the shape means more power can be used to move the car, and fuel consumption can be lower. Low wind resistance is even more vital for hybrid and electric vehicles so extensive wind tunnel research was done and the result is a body that has a Cd of 0.22, impressive considering its size.
Not visible are improvements in aeroacoustics; the new model’s quietness is said to be even better than the e previous generation which already excelled with a very high level of interior noise comfort. The high rigidity of the bodyshell provides the basis for this achievement, and is enhanced with fine-tuning.
Lounge-like interior
These days, car interiors are designed to be like lounges and not just seating spaces inside a cabin. Especially with a model like the S-Class, comfort and spaciousness are high on the list of expectations. With the new generation, the interior has fully evolved into a ‘third place’ for the occupants, between the home and workplace. So it has to be able to provide not just comfort but also be functional enough for those who want to get some work done while on the move.
The seats qualify as technological benchmarks for long-distance comfort. The complex technology inside each seat uses multiple motors for adjustments in the tiniest dimension. The flowing, 3-dimensional layer design theme gives an impression of lightness with its nappa leather upholstery. The adjustment range and angle of the front passenger seat in the chauffeur configuration and the reclining seat behind it have been improved as well.
MBUX – the Mercedes-Benz User Experience – is a big thing for the brand and has appeared in every new model since the current A-Class was launched in 2018. Since then, it has continued to evolve and gain more sophistication, with the second generation of this learn-capable system making its debut in the new S-Class.
The possibilities for personalization and intuitive operation have become far more extensive, especially in the rear. Both the hardware and software have made great advancements with brilliant displays on up to 5 large screens (in part with OLED technology). The new 3D driver display allows a spatial view at the touch of a button for the first time – a real 3-dimensional effect without having to wear 3D glasses.
The voice assistant ‘Hey Mercedes’ is constantly learning, by activation of online services in the Mercedes me App. Moreover, certain actions (like accepting a call) can be performed even without using ‘Hey Mercedes’ which, incidentally, can also be activated from the rear.
With digital and graphic displays nowadays, it’s possible to have multiple displays and not end up like the cockpit of a 1970s fighter jet. The screens can be individualized with a choice of 4 display styles and three modes (Navigation, Assistance, Service), so the driver can choose whatever information is most important to him or her when driving. Furthermore, this new version of MBUX uses 27 fewer buttons and switches, underscoring the minimalist appearance of the interior.
Rear airbag – world first
As mentioned earlier, an earlier S-Class was the first production car in the world to be fitted with an airbag. This pioneering position in safety continues with the latest generation and is demonstrated by having the world’s first rear airbags. These are integrated into the backrests of the front seats and deploy in a severe front impact. They deploy gently and protect strapped-in outer rear seat passengers against contact with the front seats.
Following the launch of the Honda City Hatchback in December, for which there are more than 5,200 bookings, Honda Malaysia has now announced the price of the City Hatchback RS e:HEV which was not revealed earlier. Without insurance, the price is RM107,783.09 and this price without sales tax will be applicable until June 30, 2022. There are 3 colour options – Ignite Red Metallic, Meteoroid Gray Metallic and Platinum White Pearl.
This is the first time that the City model is offered in a hatchback bodystyle and the flagship version also comes with e:HEV technology that uses the 1.5-litre Sports intelligent Multi-Mode Drive (i-MMD) powertrain coupled with Electric Continuous Variable Transmission (e-CVT). The hybrid powertrain produces 109 ps/253 Nm and can run in hybrid, engine or even fully electric mode, the latter available for a limited distance depending on the battery pack level.
The City Hatchback’s e:HEV system can run on just the electric motor powered by the battery pack, saving fuel and with no exhaust emissions.
However, as a hybrid electric vehicle, there is no need for recharging from an external source as the battery pack will recharge while the car is being driven. Recharging constantly takes place either by the engine or through regeneration during braking and coasting. This is therefore a more practical approach to electrification for Malaysians at this time when the network of recharging stations is still very small.
Specific to the City Hatchback are a Gloss Black front Grill, Solid Wing and Door Mirrors, and standard are LED headlights with LED Daytime Running Lights, LED front foglights, a rear spoiler and LED rear light units, along with 16-inch alloy wheels.
The interior follows the layout of the sedan and comes with red-stitched Ultrasuede® Seats. The City Hatchback offers additional versatility as it comes with the 4-mode ULTRA Seat, a feature that originated in the first Jazz. The ULTRA Seat allows for different seating layouts in the cabin to suit different usage requirements, including one for carrying tall items like plants.
With the ULTRA Seat, it is possible to fold the seats upright to create more vertical space to carry tall items like plants.
This variant also comes with a 7-inch Interactive TFT meter, 8-inch Display Audio with Apple CarPlay and Android Auto Connectivity as well as rear air conditioning. Other first-in-segment features are Honda LaneWatch to monitor the blind spot on the left side, Electric Parking Brake and Remote Engine Start.
Honda LaneWatch uses a small camera on the left door mirror to monitor the blind spot behind the car and display real-time images on the centre screen.
Like the City Sedan RS e:HEV, this hatchback variant also has Honda SENSING, the camera-based driver-assistance system which allows Level 2 autonomous driving as well. Honda SENSING consists of Adaptive Cruise Control, Collision Mitigation Braking System, Forward Collision Warning, Lane Keep Assist System, Road Departure Mitigation, Lane Departure Warning and Auto High Beam. With the systems active, the workload on the driver is less so fatigue on long journeys can be reduced as well as motoring safety being enhanced.
Honda CONNECT is also included and this smart Telematics Technology allows owners to connect with the City Hatchback via a smartphone application. The owner can be easily informed of the car’s status as well as other useful information.
For more information or to locate a showroom for a test-drive, visit www.honda.com.my.
Every sector of the auto industry has to meet carbon-neutrality targets during this target and even the brands in the uppermost segments are not exempted although their volumes may be relatively lower. While all will eventually offer models powered only by electricity (battery electric vehicles or BEVs), the transition period will see hybrid powertrains being used for electrification. It is anticipated that more than 20% of sales this year will come from the brand’s hybrid models.
Bentley already started this transition a few years ago with the Bentayga Hybrid and has followed up with the Flying Spur Hybrid. It is continuing with development of hybrid electric vehicles (HEVs) and has announced that 5 new models will be launched this year. As Bentley has only 5 model lines (including the Flying Spur and Bentayga), these new cars HEVs will likely be variants of the models, one of which will be the Continental GT.
The Bentayga Hybrid (above) and Flying Spur Hybrid (below) will be joined by 5 more hybrid models in 2022.
From 2025, the carmaker plans to launch one new BEV every year under its ‘Five-in-Five’ plan that is part of its Beyond100 strategy to reduce the brand’s environmental impact. Innovative steps will be taken to neutralise Bentley’s carbon footprint even further towards its aim of becoming carbon neutral by 2030. These include a commitment that all its global retailers will be carbon-neutral by 2025 (or sooner), with production zero impact by 2030.
To realise this strategy, Bentley has committed a sustainable investment of £2.5 billion for product development as well as transforming the factory in Crewe, England, to become a ‘Dream Factory’ – a digital, zero environmental impact, flexible and high-value manufacturing facility.
The Crewe site is already a certified carbon neutral facility, and the next initiatives will be an extension of on-site energy production with solar power. Moreover, Bentley is investigating using sustainable biofuel in fleet cars, including its Heritage Collection.
“Beyond100 is the boldest plan in Bentley’s illustrious history, and in the luxury segment. It’s an ambitious and credible roadmap to carbon neutrality of our total business system, including the shift to 100% BEV in just 8 years,” said Adrian Hallmark, Chairman and CEO of Bentley Motors, which is part of the Volkswagen Group. “Our aim is to become the benchmark not just for luxury cars or sustainable credentials but the entire scope of our operations. Securing production of our first BEV in Crewe is a milestone moment for Bentley, and the UK, as we plan for a long-term sustainable future in Crewe.”
Bentley’s sales have continued to climb and the total of 14,659 vehicles delivered in 2021 exceeded by 31% the record volume set the year before. This achievement was driven by new model introductions, a fresh product portfolio and increasing demand for the hybrid models.
While the Americas region took the most vehicles (4,212 units), it was China where Bentley saw the biggest growth of 40% to 4,033 units. The Asia Pacific region posted an increase of 37% which was also said to be a record performance as 1,651 vehicles were delivered, against 1,203 sold in 2020.
It’s been a while since Ford had a victory in the World Rally Championship (the last one was in the Rally Great Britain in 2018) and Sebastien Loeb’s win in the 2022 Monte Carlo Rally was all the more significant as it was the first one in the new hybrid era of rallying.
Loeb won using the new Ford Puma Rally1 with the British M-Sport Ford team run by Malcolm Wilson, a former rally driver as well. Aged 47, Loeb, from France, was also the oldest winner of an FIA World Rally Championship round. Loeb’s win in Monte Carlo makes it 8 for him, putting him alongside Sebastian Ogier as far as wins on the classic event are concerned.
Loeb had beaten his Ogier, who was using a Toyota GAZOO Racing Yaris Rally1, on the final day when Ogier, driving a, was given a 10-second penalty for a jump-start earlier. To make things worse, a puncture on a front tyre slowed him although he made it to the finish but by then, Loeb had ended with a 10.5-second lead. Incidentally, Ogier will only enter selected events this year after stepping away from full-time competition.
Loeb, accompanied by co-driver Isabelle Galmiche (a 50-year-old teacher), had been running behind Ogier initially but then clocked 4 fastest times consecutively to move into the lead. The Toyota driver’s puncture on the penultimate stage of the rally had lost him his lead of 24.6 seconds but he fought hard and, even with the penalty, cut the deficit down to 10.5 seconds.
Another Ford Puma, driven by Craig Breen, finished in third and added to the team’s points to gain an early lead in the Manufacturers’ championship. Fourth was an impressive result for young Kalle Rovanpera and his co-driver Jonne Halttunen, who made huge strides forward in pace and confidence in their new GR Yaris Rally1.
For the Hyundai Motorsport’s Ott Tanak, the opening round of the 2022 World Rally Championship was one to forget. Tanak, champion in 2019, and his team mates experienced troubles during the second last day and had only 2 of the new Hyundai i20 cars to finish the rally.
“We had a tough weekend,” said Thierry Neuville. “There has been a huge amount of work behind the scenes to prepare for this event, from me and Martijn, as well as the team, so to come away without any reward is hard to accept. We won’t give up. There are different areas we are going to work on but most important is the reliability.”
The WRC2 category was also fiercely contested, with Andreas Mikkelsen/Torstein Eriksen working hard to keep their titles again this year. Signs are good that they can, with victory in their Skoda Fabia Rally2 Evo ahead of Erik Cais who was in a Ford Fiesta, and Mikkelsen’s team mate in Toksport, Nikolay Gryazin.
Sami Pajari marked the start of the new-look FIA WRC3 category, which is now for Rally3 cars, beating Jan Cerny to the class win with a margin of just 7.6 seconds. Enrico Brazzoli rounded out the top three with all drivers competing in Ford Fiesta Rally3s.
The new era of WRC, which starts its 50th season this year, focusses on hybrid powertrains for the Rally1 cars, with 100 kW electric motors coupled to 1.6-litre turbocharged engines that generate at least 500 bhp. The new regulations are aimed at moving the championship towards a more sustainable future and include use of 100% hydrocarbon fossil-free fuel.
TOP 10 FINISHERS
1. Sebastien Loeb/Isabelle Galmiche | Ford Puma Rally1
2. Sebastien Ogier/Benjamin Veillas | Toyota GR YARIS Rally1
3. Craig Breen/Paul Nagle | Ford Puma Rally1
4. Kalle Rovanpera/Jonne Halttunen | Toyota GR YARIS Rally1
5. Gus Greensmith/Jonas Andersson | Ford Puma Rally1
6.Thierry Neuville/Martijn Wydaeghe | Hyundai i20 N Rally1
7. Andreas Mikkelsen/Torstein Eriksen | Skoda Fabia Rally2 evo
8. Takamoto Katsuta/Aaron Johnston | Toyota GR YARIS Rally1
9. Erik Cais/Petr Tesínsky | Ford Fiesta Rally2
10. Nikolay Gryazin/Konstantin Aleksandrov | Skoda Fabia Rally2 evo
Just as the 2022 Formula 1 World Championship will see the biggest changes in technical rules in some four decades, the 50th season of the World Rally Championship (WRC) will undergo major environmental changes as new FIA technical regulations drive the series towards a more sustainable future.
Under its PurposeDriven movement, the FIA is taking an innovation-led approach to deliver sustainable motorsport. One goal is to reach carbon neutrality by 2030. An even bigger revolution concerns the drivetrain, with hybrid technology mandatory for what are known as Rally1 cars. The plug-in hybrid unit, including all necessary components and software, will be common, with the potential for more freedom of development in 2024.
In the WRC’s first-ever rallycars with hybrid powertrains, an electric motor works together with the proven 1.6-litre turbocharged petrol engine. Rally1 cars will have up to 134 ps of additional power available in certain situations.
The unique Rally1 hybrid system has three principal modes: Full Electric Mode in which cars will have full electric range, Stage Start Mode when the system’s full power will be available, and Stage Mode in which teams and drivers will be able to create up to three personalised ‘maps’ to decide how to deploy the hybrid power. The system also provides the opportunity to reduce emissions locally via full electric driving on road sections in built-up areas.
Fundamental revisions to the technical regulations also see the top-tier Rally1 class for manufacturer teams bringing a substantial gain in crew safety with an upgraded safety cell chassis. There will also be more equality between competitors due to a new design approach.
Another milestone is the introduction of 100% sustainable fuel, a first for any FIA World Championship. Part of the FIA’s race-to-road strategy is to implement sustainable energy sources across its motorsport disciplines to reduce CO₂ emissions.
The renewable fuel from P1 Racing Fuels is a blend of synthetic and bio-derived components. This green fuel will be mandatory to all top-tier competitors at WRC events. In its development, P1 Racing Fuels will collaborate with global energy and chemical experts Aramco on the formulation of advanced-generation biofuels and sustainable synthetic fuels derived from captured CO2 and low-carbon hydrogen.
Fundamental revisions to the technical regulations also see the top-tier Rally1 class for manufacturer teams bringing a substantial gain in crew safety with an upgraded safety cell chassis. There will also be more equality between competitors due to a new design approach.
Introducing hybrid powertrains has been a key part in ensuring Toyota, Hyundai and M-Sport Ford are fully committed to the WRC from 2022 to 2024. All three teams have been testing their new cars which will debut in competition at the Rallye Monte-Carlo, the opening round of the 2022 season, next week.
(Above and below) Toyota GR Yaris Rally1
The new generation of Rally1 cars from the 3 manufacturers were shown together for the first time in Austria yesterday at a special ceremony that marked the beginning of a new era in rallying. In the presence of new FIA President Mohammed Ben Sulayem, reigning champions TOYOTA GAZOO Racing, Hyundai Motorsport and M-Sport Ford unveiled their all-new rallycars which will compete across 13 rounds on 4 continents.
(Above and below) Hyundai i20 N Rally1
(Above and below) M-Sport Ford Puma Hybrid Rally1
“Today’s launch of the new Rally1 era is a very proud and significant moment for the FIA and entire rally family and I would like to congratulate WRC Promoter for delivering a great show at the start of the championship’s 50th anniversary season,” said Ben Sulayem, a former WRC competitor himself. “The enthusiasm for the FIA’s new technical regulations has been very much in evidence in recent months and the event further underlined the momentum coming from the teams and manufacturers, with Rallye Monte-Carlo just a few days away.”
Although UMW Toyota Motor (UMWT) has been promoting hybrids a lot in the past few months, Toyota hybrids are not new to the Malaysian market. While the first model, the Prius which was the world’s first mass-produced hybrid car, was not marketed here, it did make a brief appearance in 2000 to introduce the hybrid electric technology to government officials. However, it would only be 10 years later that the government’s exemption of all duties for hybrid electric vehicles (HEVs) and battery electric vehicles (BEVs) would see UMWT selling many HEVS. It imported the Prius, by then in its third generation as well as the smaller Prius c and also the Lexus Ct200h. Without the high duties imposed, the models were attractively priced and sold well.
However, when the duty-exemption was withdrawn a few years later, prices shot up again and sales fell to zero. Although the government had hoped that the car companies would follow up after the duty-free period to assemble HEVs locally, only one company chose to do so while the others did not bother. The government instead focussed on encouraging the local assembly of ‘energy efficient vehicles’ (EEVs) for which incentives would be given to offset production costs and lower retail prices.
Last year, UMWT decided that it would move forward with a view towards electrification of its range, in line with the aim of Toyota Motor Corporation to achieve carbon neutrality by 2050. However, the company’s strategy does not entirely focus on electrification of its products to the extent that future models will no longer be powered by combustion engines in the near-term. Instead, it has a multi-pronged approach which will be determined by various factors in each country and region.
The more advanced countries have an extensive network of charging stations to support BEVs but in Malaysia, this is still something that is under development. To date, there are only around 500 charging stations in the whole country, mostly in urban areas and mainly in the Klang Valley. In Toyota’s view, that’s not a suitable situation to be introducing BEVs at this time, so it has chosen to start its electrification journey in Malaysia with HEVs. This is more practical as hybrid powertrains are not reliant on a charging infrastructure since they can recharge their battery packs on the move, and the technology cost of HEVs is lower than BEVs so they are within reach of a greater number of customers.
This led to the decision to invest RM270 million in the assembly plant and related expenditures to assemble HEVs locally. It’s the first time that a Toyota HEV is being assembled locally and though this may seem like it was prompted by the government’s efforts to promote greater electrification of motor vehicles as announced in the Budget last October, UMWT made their announcement last July, many months before the government’s announcement. In any case, the incentives are only for BEVs and HEVs will continue to receive the EEV incentives which will still help offset production costs.
Tonight, the launch of the Toyota Corolla Cross Hybrid represents the culmination of the project to assemble HEVs locally and it would be the first of a range of HEVs to come. As can be seen from the price, it is attractive enough, unlike BEVs which, even with full tax exemption, are starting from RM150,000. Since the Corolla Cross Hybrid is being assembled, UMWT has also decided to include the Corolla Cross with a 1.8-litre petrol engine as well and this is available in two variants.
As mentioned earlier, HEVs are not reliant on external charging so a customer can buy and use one just like any other car with a combustion engine. Hybrid electric technology, which has matured after 25 years, is a ‘transparent’ technology in that the driver doesn’t really see the difference (although the feel might be different). It’s just like the introduction of multivalve engines and EFI in the 1980s and turbochargers becoming common in the 2000s.
For those who may not be entirely familiar with hybrid electric technology, here’s a quick explanation. As the term suggests, the powertrain is a combination of two power sources – a petrol engine and an electric motor (actually the Toyota system has two motors). In some systems, they may work independently but Toyota’s system, now in its fourth generation, is designed to work in a collaborative manner. Running conditions and the amount of energy in the battery pack determine how the collaboration works but basically, the car will move off with only electric power and as the speed increases, the engine will provide the additional power needed to go faster.
While cruising, the system will be varying the use from each power source so at times, the electric motor may be doing all the work, which means no fuel is used and that helps in fuel-saving. It can be quite significant as we discovered on a drive from the Klang Valley to Penang where the average consumption was 6.4 litres/100 kms or 15.6 kms/litre. Other members of the media were able to get even better figures.
The motor relies on electricity supplied by the lithium-ion battery pack so what happens when there is no more? That should not happen as the amount of energy will be constantly replenished while the car is moving. This is done by regenerative braking (where energy lost during braking is converted into energy for electricity) or the generator (the second motor) charges the battery pack. In the event that there is heavy usage of electricity, then the engine will be used more as the recharging takes place.
This self-charging capability takes away the ‘range anxiety’ that users of BEVs may have. This relates to the concern about running out of electricity on a long journey. With a HEV like the Corolla Cross Hybrid, you can still move using the engine and can refuel at one of 3,700 stations all over the country. But with a BEV, you might be stranded by the side of the highway or along some remote country road. It will be a long, long time before BEV technology is so advanced that you can recharge with a portable powerbank like you do now for your mobilephone.
Battery technology has been constantly advancing since the first Prius. In the early days, the battery pack was big and heavy and did not hold a lot of electricity. Since then, the battery packs have become smaller and yet more energy-dense while using more efficient processes like lithium-ion interaction. Their cost has also come down while reliability and durability have improved. For owners’ peace of mind, UMWT offers an 8-year warranty on the battery pack and this warranty, unlike others, includes some hybrid-related systems as well. There’s also an option to extend the warranty to 10 years, but the general vehicle warranty is 5 years with unlimited mileage.
The powertrain for the Corolla Cross Hybrid has a 1.8-litre 4-cylinder petrol engine which is the same as the one in the Corolla Cross 1.8V and 1.8G. It produces 98 ps/142 Nm while the primary electric motor contributes 53 kW (equal to 72 ps) and 163 Nm of torque. Power delivery is via an E-CVT specially engineered for use in HEVs.
There are 4 modes – NORMAL | SPORT | ECO | EV – which the driver can select at the touch of a button while on the move to suit driving preferences or to maximize fuel-saving. The EV mode is a unique mode which gives an experience similar to driving a fully electric vehicle. In this mode, only the electric motor is used so there are zero emissions and the vehicle moves around noiselessly. The distance can be several hundred metres (depending on battery condition and driving speed) and would be ideal when moving around a carpark looking for a space.
The air-conditioning system in the Corolla Cross Hybrid is also unique, specially designed for HEVs. Unlike conventional air-conditioning systems which use an engine-driven compressor to pump the refrigerant around, the system is electrically powered. It can therefore run even when the engine is off, drawing its power from the battery pack. Should the battery pack capacity be low, the engine will restart to recharge it as it continues to power the air-conditioner’s electric compressor.
Appearance-wise, the Corolla Cross Hybrid is not exactly new on Malaysian roads as the non-hybrid model was introduced last April, imported from Thailand. However, due to the long period of shutdown in the middle of the year and some supply issues caused by the microchip shortage, the number on the roads is limited. Now, as a locally-assembled model, you should start to see more of them.
Where is the past, a variant bodystyle of the Corolla would still have some common elements with the sedan (usually the front end), the Corolla Cross Hybrid looks like a different model altogether. Toyota could have raised a Corolla Hatchback and ‘ruggedized’ its looks (as some manufacturers do to create a ‘SUV’) but they instead came out with a new SUV design and placed the model in the family of the all-time bestselling car in the world. To differentiate a Corolla Cross Hybrid and a non-hybrid, there are blue accents on the grille badge, logo on the engine, headlights and the rear badge.
Besides being the first Toyota HEV assembled locally, the Corolla Cross is also the first model with Toyota New Global Architecture (TNGA) to be assembled in Malaysia. TNGA has been used for all recent new models and has been engineered for variability, allowing engineers a lot of freedom to adapt it to different types of models. It is used for sedans and hatchbacks as well as SUVs and while there is differentiation in designs, there are also many common elements and parts and that is one of the secrets of reducing production costs.
The passenger car-like interior of today’s SUVs was pioneered by the Toyota RAV4 some 25 years ago. This is continued in the Corolla Cross Hybrid andthere is claimed to be significantly better headroom than other competitor SUV models in the same class. The wide body dimensions also allow the centre console to be wider for more storage space.
The blue accents on the exterior that identify the Corolla Cross Hybrid are also evident in the instrument panel. There is a colour 7-inch Multi Information Display (MID) with two styles – detailed and simple. Due to the quietness of operation, a READY indicator is shown to let the driver know when the system is ready to run when the START/STOP button is pressed.
Various types of information are presented to the driver in the MID and one of the displays shows the flow of power and electricity between the engine, motor, battery pack and wheels. The flows are shown in real-time and show the driver when the battery is being recharged and the level of electricity in it.
To help the driver of the Corolla Cross Hybrid achieve the best fuel economy, an ECO display in the instrument panel provides guidance on accelerating optimally. At the end of each journey, the driver can refer to an ECO Score to see how eco-friendly the driving style has been. With such a feature, drivers may be inspired to achieve a good score daily and save more fuel!
A large 9-inch panel in the middle of the dashboard provides information for the infotainment systems, as well as the image from the rearview camera. The system is Apple CarPlay and Android Auto ready so compatible smartphone apps can easily be transferred and accessed from the dashboard. Other connectivity options include USB mirroring, AUX and Bluetooth.
To assist the driver during parking or manoeuvering the vehicle is a 3D Panoramic View Monitor (shown above) which also uses the display on the 9-inch panel. Utilising small cameras on all sides of the vehicle, a 3-dimension view of the surroundings on all sides is presented to the driver. This not only enables easier positioning of the vehicle but also allows the driver to spot hazards or little children that might not be visible from the driver’s seat.
The air-conditioning system operated by an electric compressor has automatic operation to keep the cabin at the desired temperature. Airflow and temperature can be set differently for the driver and front passenger and with the S-Flow function, the airflow will be concentrated only on seats with people sitting on them. Cool air is also carried to the rear occupants by additional vents between the front seats.
Although a HEV has generally lower noise levels than a car with a combustion engine, additional efforts went into making the cabin quieter by adding an insulator sheet under the bonnet to isolate noise from the engine bay. The windscreen glass is also an acoustic type, reducing transmission of wind and other external noises.
Besides the convenience of a Smart Entry & Push Start System to lock/unlock the doors and start/stop the engine, the Corolla Cross also comes with a Power Back Door that opens and closes automatically by just positioning a foot under the rear bumper which has a proximity sensor. This allows for handsfree operation which will be convenient when both hands are holding bags or other items. For safety, the automatic opening will not work if the engine is running.
Instead of being installed in the boot area as in past models, the battery pack is under the rear seat, so no boot space is lost.
Besides the high-strength TNGA platform, the structure of the Corolla Cross is engineered to withstand impact forces from all sides during an accident, reducing or preventing injuries to the occupants. In crash testing and technical evaluation by ASEAN NCAP, the Corolla Cross Hybrid and Corolla Cross, as with many other Toyota models, has received a maximum 5-star safety rating.
The Corolla Cross Hybrid and Corolla Cross 1.8V come with Toyota Safety Sense (TSS) 2.0, a suite of Active Safety technologies that help a driver avoid accidents or reduce the damaging effects should a collision occur. Besides having automatic emergency braking and automatic high beam adjustment among the 5 main systems, the adaptive cruise control is also available at all speeds, maintaining a safe gap from the vehicle ahead whatever the set speed is. It can even bring the vehicle to a complete stop if the preceding vehicle stops without the driver needing to depress the brake pedal. When the vehicle ahead starts to move, it will automatically resume moving as well.
Before SUVs appeared, the stationwagon was the ideal multi-purpose vehicle to haul a lot of stuff. Sedan-like but stretched a bit to have a big boot space, it was as low as a sedan and just as comfortable. Volvo, which had been making stationwagons since 1953 when it introduced the Duett, became a leader in the stationwagon segment in the 1980s, especially in Europe where its models were popular.
The Duett had been conceived as a vehicle which could be used for work as well as for family use, so it was the original dual-purpose vehicle (a term which came into use in the early 1980s when the first 4x4s like the Mitsubishi Pajero and Isuzu Trooper were introduced). The success of the Duett encouraged the Swedish carmaker to continue making such cars and in the years that followed, it would always have a stationwagon variant of the prevailing model series. Malaysian motorists will remember the police using Volvo stationwagons in the 1970s and then the 850 stationwagon in the 1990s for highway patrol work.
And although in the 21st century, it has been selling more SUVs than sedans and stationwagons, the company has assured stationwagon fans that it will continue to offer such models in future. These will be alternatives to the SUV and crossover ranges and will eventually be fully electric. They are currently designated as S and V models although these may change as the future models will have more aerodynamic forms. Volvo had originally wanted to designate its stationwagons as ‘F’ – for ‘Family’ – when it launched the first V40. However, Ferrari sent a note of protest and said that a ‘F40’ would mislead people into thinking of the sportscar made by the Italian carmaker which had the designation. So Volvo switched to ‘V’, which it said meant ‘Versatility’.
In the US market, which has been a huge consumer of Volvo stationwagons for decades, some of the models are no longer being sold (which led to the rumour of Volvo stopping stationwagons altogether). However, the company will still sell some versions of the current models and in Malaysia, the latest V60 Recharge T8 has just gone on sale with a price of RM287,474 for the Inscription version (the only one available).
This is an electrified PHEV model with a plug-in hybrid Drive-E powertrain. There is a turbocharger and supercharger which boost output to 320 bhp/400 Nm, to which is added the output of an electric motor that can generate up to 407 ps/640 Nm. A lot of power to all 4 wheels which provides effortless cruising even when the 519-litre boot is fully loaded.
As a PHEV, the V60 Recharge T8’s battery pack can be recharged from an external power source rather than just being recharged while on the move. The time for recharging varies depending on the type of charging used. If from a normal household power socket, each hour of charging can provide 7 to 14 kms but if using DC fast-charging 150 kW station, then in 10 minutes, the battery pack can ‘fill up’ for up to 100 kms of range at a 150 kW station. Shell recently started operations of a DC fast-charging station at its station near Tangkak in Johor and will establish a network of 12 stations along the North-South Expressway.
With a fully charged battery pack, it can travel a claimed 49 kms on just electric power but in normal driving, the system will be continuously varying the use of the two power sources for optimum efficiency. Unlike a fully electric powertrain which will come to a standstill if the battery pack is empty, a PHEV like the V60 Recharge T8 will still be able to run using its petrol engine.
As for the design, the V60 Recharge T8 maintains the sleek form which has been around since the days when Peter Horbury, the company’s former design head, declared that ‘we kept the toys and threw out the box’ as he introduced the C70 coupe in 1996. Thereafter, Volvo stationwagons no longer looked like boxes on wheels and had a streamlined profile that added elegance.
The interior too is what you would expect of a Volvo with their Scandinavian ambience and focus on functionality. These days, the emphasis is on using sustainable materials and ensuring that the cabin air is as clean as possible. And although the environment is like that of a premium sedan, there is still the versatility of a SUV with rear seats that fold down and extend the length of the boot.
“The addition of the Volvo V60 Recharge T8 as a PHEV brings Volvo another step forward in our electrification strategy. We are one step closer to realising our aspirations in having a fully electric line-up by 2030 as we move further into a more sustainable future,” said Charles Frump, Managing Director of Volvo Car Malaysia.
Toyota hybrids aren’t new in Malaysia and although the early ones were not sold here, there was a short period about 10 years ago when UMW Toyota Motor imported the third generation of the Prius (the first mass-produced hybrid car in the world) as well as the smaller Prius c and also the Lexus CT200h. During that period, the government had allowed hybrids and EVs to be sold duty-free, so they were priced attractively. After the government stopped the duty exemption, the prices went up again due to high import duties as well as the higher cost of hybrids, and demand for hybrids fell.
Now, as there is an increasing need to address climate change, especially global warming, carmakers like Toyota are using various approaches to ensure that ‘no customer is left behind‘. Toyota recognises that different countries and different regions may be at different stages of development with regards to the infrastructure to support electrified vehicles. In the more advanced regions like Europe, Japan and North America as well as China, the network of recharging stations is extensive so owners of electric vehicles can easily find a place to recharge their vehicle.
In Malaysia, while the government has just started to give support to promoting fully electric vehicles, the infrastructure is not yet developed enough. There are only around 400 recharging stations in the country at this time and most are are the bigger cities and towns. In view of this, UMW Toyota Motor has taken the position that hybrids are a better approach for now as they do not require the infrastructure since they are self-charging. And besides, there are around 3,700 petrol stations all over the country so refuelling is easy enough.
Owners of hybrid vehicles can travel as far as those with vehicles using petrol or diesel combustion engines, and have no fear of running out of ‘fuel’ in the battery pack. The hybrid system thus offers the benefits of electric drive without the issues of recharging and ‘range anxiety’ where the motorist has to worry if he or she can find a place to recharge – not to mention the fact that recharging is not as fast as refuelling petrol.
To increase the usage of hybrids, UMW Toyota Motor has therefore decided to assemble some models in Malaysia at its own plant. The first of these is the Corolla Cross Hybrid which will be launched this week with a price of around RM137,000. It is the first Toyota hybrid model assembled in Malaysia and also the first model with the Toyota New Global Architecture (TNGA) that is assembled locally. Besides the 5-year/unlimited mileage warranty, there is also a separate warranty on the battery pack that is 8 years long (with the option of extending to 10 years). Unlike other battery warranties, the warranty for the Corolla Cross Hybrid covers a few additional hybrid-related components as well. So those who have had concerns about the high cost of replacement if there is a problem can have peace of mind.
We’ve driven the Corolla Cross Hybrid from the Klang Valley to Ipoh and then Penang and back and we have first impressions to share with you in this video.
To know more about the Corolla Cross Hybrid, visit www.toyota.com.my.
As the flagship of the Mercedes-Benz range, the S-Class has typically been the centerpiece of the brand. Each generation since the W 187 of 1951 has introduced new technologies, advancing safety, performance, comfort and quality. The pioneering technologies have influenced automotive engineering of its era, eventually trickling down as they became more affordable.
More than 4 million S-Class limousines have been delivered worldwide since the early 1970s when the ‘S-Class’ designation was used. Over 18,000 of those have been sold in Malaysia, where the model has been assembled locally for the past few generations. Assembled under contract in earlier years, the model has been assembled at Mercedes-Benz Malaysia’s own production facility in Pekan, Pahang, since 2007.
Today, the seventh generation of the model – also assembled at the Pekan plant – arrives in the market, a bit over a year after it made its global debut in Germany. Only one version is current offered – the S 580e – which is a long-bodied version. The price could not be confirmed in time for the launch although it will be more than the previous generation, according to Michael Jopp, Vice-President, Sales & Marketing Passenger Cars, at Mercedes-Benz Malaysia. He added that first deliveries will start from mid-January, but the waiting period is already stretched to the end of the first quarter of 2022.
‘580’ doesn’t mean 5.8 litres
The number of the model designations of many of today’s German cars no longer indicate displacement or cylinders as they once did. For instance, with the old 380SE, at least you knew the engine size was 3.8 litres. But with the new ‘580’, it is not 5.8 litres and the engine is actually an in-line 6-cylinder petrol engine of 3 litres and it is part of a plug-in hybrid powertrain (PHEV) with an electric motor.
The engine’s output is 367 bhp/270 kW with 500 Nm of torque available between 1,500 and 4,500 rpm, while the motor generates 110 kW with 440 Nm that comes on almost instantaneously. The combined output can propel the S 580e from 0 to 100 km/h in a claimed 5.2 seconds and up to a top speed of 250 km/h. If conditions permit, it is possible to run only on electricity for up to 100 kms. When the battery is empty, ‘refuelling’ will take up to 2.5 hours, depending on the charging method.
Hybrid powertrains are not new to Mercedes-Benz models in Malaysia and the company has sold them, even in the S-Class, some time. One concern owners have is the cost of the battery pack if it needs to be replaced as it is pretty expensive. But for the first 8 years or a maximum of 100,000 kms, Mercedes-Benz will provide warranty coverage which should offer some peace of mind.
Showcase for new technologies
As with every generation before, the new S-Class brings with it new and advanced technologies. One of them is DIGITAL LIGHT, which emanates from each headlamp. The light module has 3 extremely powerful LEDs with light that is refracted and directed by 1.3 million micro-mirrors. The resolution is therefore more than 2.6 million pixels per vehicle, allowing highly precise light distribution.
DIGITAL LIGHT also makes Highbeam Assist over 100 times more precise than 84-pixel light when excluding oncoming traffic or road signs from the light beam. Light/shadow graduations and the light distribution of all the other adaptive light functions are also realised with considerably more precision, optimising illumination in all ambient lighting conditions.
The aerodynamic efficiency is also very impressive, considering the size of the car. It is 0.22 Cd, which is one of the lowest figures in the world for a production sedan. The lower wind resistance of the shape means more power can be used to move the car, something that is highly beneficial with hybrid and electric powertrains. This has been achieved by lengthy wind tunnel research and then applying aerodynamic measures to various areas of the body, underbody and detachable parts.
Not visible are improvements in aeroacoustics; the new model’s quietness is said to be even better than the e previous generation which already excelled with a very high level of interior noise comfort. The high rigidity of the bodyshell provides the basis for this achievement, and is enhanced with fine-tuning.
Some examples are the apertures for the cable grommets in the firewall which have double seals, effectively stopping noise from the engine bay seeping through. To achieve an engine sound that is perceived as refined and unobtrusive in the interior, the firewall insulation has been extended into the side areas of the A-pillars and the floor area. Acoustic foam in certain bodyshell sections is also used for the first time.
Even with local assembly, Mercedes-Benz Malaysia follows the brand’s global policies to promote sustainability. This is possible as environmental aspects were already taken into account in the conceptual phase. More than 98 kg of components, derived from resource-conserving materials, are used in the S-Class. The number of components containing recyclates is now 120 – more than twice as many as in the preceding model. Another 40 kgs or so are made from renewable raw materials.
‘Third place’ lounge-like interior
The S-Class, with its limousine proportions, has always offered its occupants comfortable travel in a relaxing environment. With the new generation, the interior has fully evolved into a ‘third place’, a refuge between the home and workplace which many spend a lot of time in (at least in the pre-pandemic days when travel to and from office was the daily norm).
As with all Mercedes-Benz models in recent times, MBUX (Mercedes-Benz User Experience) is a highlight. Interestingly, it was one of the few significant new technologies that did not start in the S-Class but in the new A-Class launched in 2018. Since then, it has continued to evolve and gain more sophistication.
The second generation of this learn-capable system now debuts in the new S-Class. The possibilities for personalization and intuitive operation have become far more extensive, especially in the rear. Both the hardware and software have made great advancements with brilliant displays on up to 5 large screens (in part with OLED technology). The new 3D driver display allows a spatial view at the touch of a button for the first time – a real 3-dimensional effect without having to wear 3D glasses.
Using cameras in the overhead control panel and learning algorithms, MBUX Interior Assist recognizes and anticipates the wishes and intentions of the occupants. It does this by interpreting head direction, hand movements and body language, and responds with corresponding vehicle functions. As well as enhancing operating convenience, MBUX Interior Assist improves safety. Even before the journey begins, it notifies the driver if the camera has detected a child seat on the front passenger seat but the seatbelt is not fastened, for example.
The system now has a fingerprint scanner just below the central display which unlocks access more conveniently, yet securely, than entering a PIN. Also available is the MBUX Augmented Reality Navigation which connects the virtual world with the real world. The technology incorporates graphical navigation instructions and traffic information into live images to ensure drivers will reach safely and stress-free,
The voice assistant ‘Hey Mercedes’ is constantly learning, by activation of online services in the Mercedes me App. Moreover, certain actions (like accepting a call) can be performed even without using ‘Hey Mercedes’ which, incidentally, can also be activated from the rear.
Revolution in interior design
Just as with introducing new technologies to the car, the interior designers have also strived to create a revolutionary interior design, including associations with interior architecture and yacht design elements. The sculptured look of the dashboard, centre console and armrests appears to float above an expansive interior landscape. The systematic reduction in the number of controls underscores the minimalist appearance of the interior. A fine divide between the upper section of the dashboard and the large trim element structures the area and creates horizontal breadth.
The driver display and media display offer a comprehensive aesthetic experience. The appearance of the screens can be individualized with a choice of four display styles (Discreet, Sporty, Exclusive, Classic) and three modes (Navigation, Assistance, Service). New design elements include the flat, 4-square centre vents with horizontal nacelles, rather than the sportier turbine-like vents in other models.
Besides 5 screens, other highlights in the cabin include large areas of trim in the dashboard and in the rear. These flow around the passengers and are a systematic further development of the wrap-around effect. The Anthracite open-pore poplar wood trip lends the interior an individual look.
Even in the seats, Mercedes-Benz has made such they qualify as technological benchmarks for long-distance comfort. The complex technology inside the seats uses multiple motors for adjustments in the tiniest dimension. The flowing, 3-dimensional layer design theme gives an impression of lightness with its nappa leather upholstery. The adjustment range and angle of the front passenger seat in the chauffeur configuration and the reclining seat behind it have been improved as well.
Thanks to LED technology, the new S-Class has also taken a leap forward in its interior lighting with interactive interior lighting for the first time. The active ambient lighting supplements ambient lighting with an additional layer of light. It is integrated into the driving assistance systems, and is able to reinforce alerts visually. This also makes corresponding feedback possible for the comfort systems. This applies to the climate control system or the ‘Hey Mercedes’ voice assistant.
Offered as standard with the new S-class is a Burmester 3D surround sound system. The German specialist in audio systems has been providing custom-developed sound systems for Mercedes-Benz model since 2013. The sound emanating from the high-quality speakers can be specifically optimized for the front and rear seats to give a very personalized listening experience.
Continued leadership in safety
In the area of safety, Mercedes-Benz has certainly held a leadership position, often developing and introducing more advanced safety features and systems. The S-Class, being the flagship, has had the honour of being the first model with new safety technologies. One example is the airbag, which made its first appearance in a production car in 1980 when the S-Class (W126) was launched. It was initially only for the driver and then the passenger also got one, and today, there are airbags on the sides of the cabin as well and one to protect the driver’s knees.
The new S-Class again takes a pioneering role by having the world’s first rear airbags. These are integrated into the backrests of the front seats and deploy in a severe front impact. They deploy gently and protect strapped-in outer rear seat passengers against contact with the front seats. The loads on the head and neck can thus be reduced significantly.
With the new S-Class, Mercedes-Benz comes another big step closer to its vision of accident-free driving. The driver is supported by numerous new or extended driving assistance systems that reduce the driving workload in daily motoring and fatigue on long journeys. This leads to better alertness behind the wheel and therefore safer motoring.
However, there may be situations where the driver might not react in time, and this is where the assistance systems come in. They can detect other vehicles and (at very high speeds) determine the possibility of an accident, and activate the brakes if no action is taken by the driver. The emergency braking functions serve to protect other road-users, too. The operating principle of the systems is made visible by a new display concept in the driver display. Thanks to improved environmental sensors, the parking systems also give the driver even better support when maneuvering at low speed.
The PRE-SAFE system, which has been present for some time in Mercedes-Benz models, has comprehensive protective measures to reduce injuries during accidents. Upon detection of a likely impact, it can prepare the occupants for a side-on collision and reduce the risk of injury. Like a bodyguard, it pushes the driver or front passenger away from the danger zone towards the inside. The impulse is created by the movement of the seat side bolsters in the front backrests.
Besides innovations in restraint systems, the intelligent bodyshell design uses a new aluminium hybrid body shell. The content of the lightweight material exceeding 50% meets numerous requirements while lowering weight and contributing to better handling and ride comfort.
